How to Install Led Halo Fog Lights on a 2012 Jeep Wrangler?

This step-by-step guide will show you how to install LED halo fog lights on your 2012 Jeep Wrangler. These fog lights will give your Jeep a unique look and improved visibility in foggy conditions.

Checkout this video:

Tools and Materials Needed

In order to complete this project, you will need the following materials and tools:
-A 2012 Jeep Wrangler
-Led halo fog lights
-Wiring harness
-Pliers
-Screwdriver

Preparing the Jeep Wrangler

Before you begin the installation process, it is important to make sure that your Jeep Wrangler is prepared. This includes ensuring that the battery is disconnected, the front end is supported, and that you have all of the necessary tools. You will also want to review the instructions that came with your Led Halo Fog Lights to familiarize yourself with the process.

Installing the Led Halo Fog Lights

Jeep Wrangler 2012 LED halo fog lights can be a great addition to your Jeep. They provide extra light output and a distinctive look that will make your Jeep stand out from the crowd. Halo fog lights are available in many different styles, but the most popular are the LED halo fog lights. LED halo fog lights are more expensive than traditional halogen bulbs, but they last much longer and use less power.

To install LED halo fog lights on your 2012 Jeep Wrangler, you will need the following tools:

-T20 Torx bit
-Phillips screwdriver
-Drill with 1/8″ drill bit
-Wire stripper/cutter
-3/4″ hole saw or step drill bit
-Razor blade or utility knife
-LED halo fog light assembly
-Vehicle specific wiring harness (available from your local automotive store)

First, you will need to remove the factory fog light bezels using the T20 Torx bit. There are two screws that secure each bezel to the bumper. Once the screws are removed, pull the bezels away from the bumper to release them. Next, use the Phillips screwdriver to remove the two screws that secure each factory fog light to the bracket. Pull the factory fog lights out of the brackets and disconnect the wiring harnesses.
Now it’s time to install your new LED halo fog lights. Start by drilling a 3/4″ hole in the center of each bumper opening using a hole saw or step drill bit. Be careful not to drill too deeply and damage any vital components behind the bumper. Next, run the wires for each LED halo light through the drilled holes and connect them to your vehicle specific wiring harness according to manufacturer instructions.
If your Jeep is not already equipped with aftermarket front turn signals, you will need to splice into your front turn signal wire in order to make your LED halo fog lights work correctly with your turn signals. To do this, use a wire stripper/cutter to remove about six inches of insulation from your turn signal wire. Then, using 16 gauge wire, connect one end of your new wire to the cut end of your turn signal wire and connect the other end of your new wire to one of your LED halo wires according to manufacturer instructions. Once all of the wires are connected correctly, tuck them into place and replace all of the factory bezels and screws that you removed earlier. Test your new LED halo fog lights before hitting

Tips and Tricks

Installing LED halo fog lights on your 2012 Jeep Wrangler can be a great way to improve its appearance and visibility in bad weather. However, there are a few things you should keep in mind to ensure a successful installation.

First, make sure you have the right tools for the job. You’ll need a Phillips head screwdriver, a flat head screwdriver, and a socket wrench.

Next, disconnect the battery to avoid electrical shocks.

Then, remove the old fog light assembly by removing the screws that hold it in place. Be careful not to drop or damage the assembly as you remove it.

Now, take your new LED halo fog light assembly and connect it in place of the old one. Screw it in tightly so that it’s secure.

Finally, reconnect the battery and turn on your Jeep Wrangler to test the new lights. If they’re working properly, you’re all set!

Final Thoughts

Before you attempt to install LED halo fog lights on your 2012 Jeep Wrangler, it is important to consult with a professional. This will ensure that you do not damage your vehicle in the process. Additionally, it is important to read all instructions carefully before beginning the installation process. With a little bit of knowledge and the right tools, you can easily install LED halo fog lights on your 2012 Jeep Wrangler.

Scroll to Top